Products / Drilling / Modular drills

WINVERA / MODULAR DRILLING

Modular Drill Bodies & Replaceable Head Systems

A modular drill (also called a replaceable-head drill, RHD modular drill, or crown drill) pairs a reusable steel drill body with a carbide cutting head or tip. You select the body for hole diameter and drilling depth (L/D), then match a head geometry and grade to the workpiece—without replacing the entire tool when the cutting edge wears. Winvera modular families (WVT, WVC, WVV, WVFI and WVFK) keep body and head interfaces within each family; diameters and depth groups are listed in the tables below.

How to choose a modular / crown drill
A short buyer guide: diameter and L/D first, then WVT / WVC / WVV / WVFI / WVFK — with when modular beats solid carbide. Read the selection guide →

01 / PRODUCT FAMILIES

Find your drilling system

WVT modular drilling system

WVT

Replaceable carbide heads in PG, GG, PL, MG, E and PCM geometries.

WVFI assembly

WVFI / WVFK

Two drilling families with separate body and head selections.

WVC drill body

WVC

GG drill tips with R3, R5, R7 and R10 body groups.

WVV modular drill head and drill body

WVV

Modular bodies, A3 / B3 modules, centre tips and peripheral inserts.

02 / PRODUCT FINDER

Find your modular drilling tools

Product finder

ProductFamilyDiameter / size
mm
Usable length
L/D
Details
WVT R3 Drill BodiesWVT11.00–52.99D13 × DView details →
WVT R5 Drill BodiesWVT11.00–52.99D15 × DView details →
WVT R7 Drill BodiesWVT11.00–52.99D17 × DView details →
WVT R10 Drill BodiesWVT11.00–52.99D110 × DView details →
WVT R12 Drill BodiesWVT11.00–52.99D112 × DView details →
WVT E Drill HeadsWVT16.00–40.00D1View details →
WVT GG Drill HeadsWVT12.50–40.00D1View details →
WVT MG Drill HeadsWVT12.50–40.00D1View details →
WVT PCM Drill HeadsWVT12.50–40.00D1View details →
WVT PG Drill HeadsWVT12.50–54.00D1View details →
WVT PL Drill HeadsWVT12.50–40.00D1View details →
WVC R3 Drill BodiesWVC12.00–37.99Dc3 × DView details →
WVC R5 Drill BodiesWVC12.00–37.99Dc5 × DView details →
WVC R7 Drill BodiesWVC12.00–37.99Dc7 × DView details →
WVC R10 Drill BodiesWVC12.00–25.99Dc10 × DView details →
WVC GG Drill TipsWVC12.00–37.99DcView details →
WVV R4 Drill BodiesWVV4 × DView details →
WVV R5 Drill BodiesWVV5 × DView details →
WVV R6 Drill BodiesWVV6 × DView details →
WVV R7 Drill BodiesWVV7 × DView details →
WVV R8 Drill BodiesWVV8 × DView details →
WVV R9 Drill BodiesWVV9 × DView details →
WVV R10 Drill BodiesWVV10 × DView details →
WVV R11 Drill BodiesWVV11 × DView details →
WVV R12 Drill BodiesWVV12 × DView details →
WVV A3 Drill ModulesWVVView details →
WVV B3 Drill ModulesWVVView details →
WVV PG Drill TipsWVV15.00–40.00D1View details →
WVV PL Drill TipsWVV15.00–40.00D1View details →
WVV WCMT Cutting InsertsWVVView details →
WVV WDXT Drilling InsertsWVVView details →
WVFI R1 Drill BodiesWVFI10.00–32.00D11 × DView details →
WVFI R3 Drill BodiesWVFI10.00–32.00D13 × DView details →
WVFI R5 Drill BodiesWVFI10.00–32.00D15 × DView details →
WVFI R8 Drill BodiesWVFI10.00–32.00D18 × DView details →
WVFI P Drill HeadsWVFI10.00–32.90DCView details →
WVFK R1 Drill BodiesWVFK12.00–26.00D11 × DView details →
WVFK R3 Drill BodiesWVFK12.00–26.00D13 × DView details →
WVFK R5 Drill BodiesWVFK12.00–26.00D15 × DView details →
WVFK R8 Drill BodiesWVFK12.00–26.00D18 × DView details →
WVFK R12 Drill BodiesWVFK12.00–26.00D112 × DView details →
WVFK E Drill HeadsWVFK12.00–26.00D1View details →
WVFK PG Drill HeadsWVFK12.00–26.00D1View details →

03 / SELECTION

How to select a modular drill body and head

1. Diameter and depth first

Choose the shortest L/D that reaches the hole.

2. Pick family

WVFI/WVFK smaller (~Ø10–33); WVT broad geometries; WVC GG tip + R3–R10; WVV large (body IF + module IF must match).

3. Match cutting component within that family only

No cross-family mixing — keep body and head interfaces within the same Winvera family.

4. Material → geometry (and grade)

After you lock diameter, L/D and family, choose the carbide head geometry for the workpiece group, then confirm the grade on that head’s Application Data. The matrix below is the WVT starting map (ISO P / M / K / N / S). Exact diameter bands, coatings and cutting data stay on the linked head pages—do not treat this hub table as a cutting-data sheet.

ISO group Start geometry Typical grades Head pages
P — steel PG first
also GG, PL, E, PCM
WV3015: P M K
WV3010: P M K S (PG)
PG · GG · PL · E · PCM
M — stainless MG first
also PG, PL, E, PCM
MG: WV3015 M · WV3010 M MG (+ PG/PL/E/PCM)
K — cast iron GG or PG
also PL, E, PCM
GG: WV3015/WV3010 P K GG · PG
N — non-ferrous PCM WV3015: P M K N S PCM
S — heat-resistant / Ti PCM or PG
where S is listed
PCM WV3015 includes S
PG WV3010 includes S
PCM · PG

Geometry quick legend (WVT)

PG — general first pick · Ø12.50–54 · WV3015 (P M K), WV3010 (P M K S)
GG — lower force, P/K · Ø12.50–40 · WV3015/WV3010 (P K)
PL — guidance / less burr · P M K · Ø12.50–40
MG — stainless-first · Ø12.50–40 · WV3015/WV3010 (M)
E — flat / ~180° bottoms · P M K · Ø16–40
PCM — centering / pre-drill · widest incl. N,S · Ø12.50–40 · WV3015 (P M K N S)

Other families — do not paste the WVT table onto them

WVC — GG tip only with R3/R5/R7/R10 · see WVC GG tips
WVV — PG/PL tips + inserts/modules · body IF must match module IF · WVV series
WVFI / WVFK — confirm geometry on the WVFI/WVFK series page

Rule: material group → geometry → grade. Final combo from the head’s Application Data. Unclear alloys: RFQ with grade and hardness.

5. Confirm coolant, screws/keys, shank fit and runout

Coolant capability depends on the exact body and head pair—Winvera does not publish one universal bar or MPa value for every modular assembly. Before the first cut, work this checklist against the body and head Application Data and your machine:

  1. Confirm the body is specified for through-tool coolant if the process needs internal coolant.
  2. Check seals, fittings and holder passages so the coolant path is continuous to the head.
  3. For longer L/D groups (about 8×D–12×D), prefer reliable internal coolant and chip evacuation; do not increase overhang without confirmed coolant delivery.
  4. Use only the screws / keys supplied for that documented body–head pair.
  5. Verify shank / holder fit and measure runout before cutting.
  6. Never mix heads across WVT, WVC, WVV, WVFI or WVFK. On WVV, body IF and module IF must match.

Exact vc / f and coolant pressure limits: use Application Data on the selected SKU pages—do not invent numbers on this hub.

04 / QUICK ANSWERS

Modular drilling questions

A modular drill is a two-part system: a reusable steel drill body plus a carbide cutting head or tip. Industry terms such as RHD and crown drill map to Winvera families WVT, WVC, WVV, WVFI and WVFK.
RHD is an industry term for replaceable-head drill. It does not mean a cross-brand interface. Match bodies and heads within the same Winvera family only.
No. Use the same family only. For WVV, the body IF must match the module IF.
Choose the shortest L/D that reaches the hole. Deeper holes need more coolant and rigidity. See the product tables on this page.
Use modular drills for the diameter and depth ranges listed on this page. For shallow indexable insert drilling, see WVU R2–R5.
On the WVT system, start from the material→geometry matrix on this page: PG is the general-purpose first pick for many steels; MG is stainless-first; GG favours lower force with a P/K bias; PL emphasises guidance and less burr; E is for flat / ~180° bottoms; PCM covers centering / pre-drill duties and lists the widest groups including N and S. Confirm grade (WV3015 or WV3010 as listed) and cutting data on the linked head Application Data. WVC uses GG tips only; WVV uses PG/PL tips plus inserts/modules; WVFI/WVFK geometries must be confirmed on the series page. Do not mix families.
Match the through-coolant capability of the chosen body–head pair, keep seals and fittings intact, and prefer reliable internal coolant on longer L/D tools. Use the correct screw/key kit, verify shank fit and runout, and keep body and head inside one Winvera family (on WVV, body IF = module IF). There is no single published coolant pressure for every modular assembly—follow the Application Data for that SKU and your machine limits.

APPLICATION SUPPORT

Specify the hole. Select the system.

Send the hole diameter, depth, workpiece grade, hardness and machine connection with your enquiry.

sales@winveratools.com
Scroll to Top